欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 常见问题

    如何验收环氧地坪工程?环氧地坪验收标准

    2018-11-04 06:50:02 无锡盛发地坪科技有限公司 阅读

    验收环氧地坪工程具体内容:1.打磨清理待修补部分地面;质量要求及验收标准:凡是待修补地面部分,均应该露出水泥地面的新鲜层或旧涂层的新鲜层,以保证所施工环氧底涂与原地面有良好的粘结力;打磨完后应该将待施工地面灰尘杂物清理干净。

    Specific contents of acceptance and acceptance of epoxy flooring project: 1. grinding and cleaning parts of the ground to be repaired; quality requirements and acceptance criteria: all parts of the ground to be repaired should expose the fresh layer of the cement floor or the fresh layer of the old coating, in order to ensure that the eptance of the construction eptance of epoxy primer and the original good bonding force of the ground; after grinding, the construction should be completed. Clean up dirt and dust. 

    2.高渗透性环氧树脂底油一遍,自然固化;(底涂)

    2. high permeable epoxy resin base oil, solidified naturally; (primer) 

    质量要求及验收标准:滚涂底油时应使其涂层均匀,无漏涂;底油完全固化后应形成一层透明的环氧树脂涂层。

    Quality Requirements and Acceptance Standards: When rolling the base oil, the coating should be uniform and leak-free; after the base oil is completely cured, a transparent epoxy resin coating should be formed. 

    3.以环氧树脂中涂材料镘刮一遍,自然固化;(中涂)

    3., the epoxy resin coated material is scraped and naturally cured. 

    质量要求及验收标准:根据修补层的厚度确定要加入石英砂的粗细(50-100目),该砂浆层一次施工厚度最好不应超过2mm。砂浆层施工完毕后应让其完全固化后方能施工下一道工序。中涂完全固化的标准为:受到重压后不会出现凹陷。

    Quality requirements and acceptance criteria: According to the thickness of repairing layer, the thickness of quartz sand (50-100 mesh) should be added, and the thickness of the mortar layer should not exceed 2 mm at a time. Mortar layer should be completely solidified after construction, and then the next process can be constructed. The standard for complete curing is: no dents will be felt after heavy pressure. 

    4.打磨机打磨中涂层;

    4. grinding machine to polish the coating; 

    质量要求及验收标准:要求打磨后的砂浆层平整,平滑,表面无凸起。

    Quality requirements and acceptance criteria: the required mortar layer is smooth and smooth without surface bulging. 

    5.双组分环氧树脂自流平面涂料按比例调配,镘刀施工自然固化(面涂)

    5. two-component epoxy self flow flat coating is proportionally distributed, and the construction of the trowel is naturally solidified (surface coating). 

    质量要求及验收标准:施工面涂之前必需保证地面清洁,表面不能有砂粒、杂物等;施工车间厂房要求完全封闭。

    Quality Requirements and Acceptance Standards: Before painting the construction surface, it is necessary to ensure that the ground is clean, and the surface should not contain sand, sundries, etc. The workshop should be completely closed. 

    6.养护

    6. maintenance 

    质量要求及验收标准:封闭场地,严禁行人行车,表面不得洒落杂物等。

    Quality requirements and acceptance criteria: closed space, no pedestrians driving, no surface debris.

    验收环氧地坪工程技术指标:

    Acceptance of epoxy floor engineering technical indicators: 

    干燥时间 表干 ≤4

    Drying schedule is less than 4. 

    实干 ≤24

    Actual work is less than 24 

    附着力(级) ≤1

    Adhesion force (grade) is less than 1 

    铅笔硬度 ≥2H

    Pencil hardness is more than 2H 

    耐冲击性 50通过

    Impact resistance 50 passes 

    柔韧性 1㎜通过

    Flexibility 1 pass 

    耐磨性(750g/500R,失重g)≤0.03

    Wear resistance (750g/500R, weightlessness g) is less than 0.03. 

    耐水性 48小时无变化

    No change in water resistance for 48 hours. 

    耐30%硫酸 7天无变化

    Resistant to 30% sulfuric acid for 7 days without change. 

    耐40%氢氧化钠 7天无变化

    40% NaOH resistant for 7 days without change. 

    耐汽油 120# 7天无变化

    Gasoline resistant 120# remained unchanged for 7 days. 

    耐润滑油 7天无变化

    No change in lubricating oil for 7 days. 


    环氧地坪工程验收标准:

    Acceptance criteria for epoxy floor project: 

    1、环境温度为25℃时,施工后2-3天应达到实干,即硬度达到完成固化的80%左右;

    1. When the ambient temperature is 25 C, the hardness should reach about 80% of the solidification after 2-3 days of construction. 

    2、表面不能出现发粘现象;

    2, the surface can not appear sticky phenomenon; 

    3、气泡:平涂型、砂浆型无气泡,自流平允许1个小气泡/10平方米;

    3, bubble: flat coated, mortar type no bubbles, self leveling allows 1 small bubbles /10 square meters; 

    4、流平性好,无镘刀痕,大面积接口处基本平整;

    4, good leveling, no trowel marks, large area of the interface is basically smooth. 

    5、无浮色发花,颜色均匀一致,大面积接口处允许有极不明显的色差;

    5, no floating color and flower, uniform color, large area interface allows very insignificant chromatic aberration; 

    6、无粗杂质,但允许有空气中的 浮尘掉落在造成的极小缺陷;

    6, there is no coarse impurity, but it allows the floating dust in the air to drop into the minimal defect. 

    7、环氧地坪表面应平整平滑,光泽度应达到设计要求(高光泽≥90、有光≥70、半光50~70),平涂型为有光、水性为半光~无光;

    7. The surface of the floor should be smooth and smooth, and the glossiness should meet the design requirements (high gloss (> 90), gloss (> 70), half gloss (> 50-70). The flat coating type should be glossy and water-based should be half glossy (~dull). 

    8、桔皮、砂浆防滑面效果应很明显。

    8, orange peel and mortar anti slip surface effect should be very obvious. 


    标签:   环氧地坪 地坪 环氧地坪漆 环氧地坪施工
    无锡环氧地坪 技术支持:【易商科技】