欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 环氧地坪

    厂家揭示环氧地坪怎样施工呢?施工步骤

    2018-11-04 06:28:18 无锡盛发地坪科技有限公司 阅读

    下面为大家介绍环氧地坪施工步骤:一、基础处理1、用研磨机进行全面打磨。让破损、起沙、粘度不牢、开裂、空鼓之部位完全暴露出来;并将浮起的砂浆、旧环氧地坪水泥结块等打磨平整。2、有松动、裂缝或脱层的地面,必须彻底打磨至密实基层,保证地面的粘结度3、将基层表面的浮灰、污染物等垃圾清理干净,确保基层表面的干净度。4、将处理过的地面清洁。

    Following is an introduction to the construction steps of epoxy floor: 1. Foundation treatment 1. Comprehensive grinding with a grinder. Let the damaged, sand-lifting, weak viscosity, cracking, empty drum parts completely exposed; and the floating mortar, old epoxy cement caking and other grinding flat. 2. Grounds with loose, cracked or delaminated surfaces must be thoroughly polished to a compact base, ensuring the cohesion of the ground 3, cleaning up the floating ash and pollutants on the base surface, and ensuring the cleanliness of the base surface. 4. Clean the treated ground. 

    检验方法:经处理后,环氧地坪表面平整、密实、干燥,无油污、且没有松动易碎颗粒,方可进行下一工序施工。

    Inspection method: After treatment, the floor surface is smooth, compact, dry, no oil pollution, and no loose and fragile particles, before the next process of construction can be carried out. 

    伸缩缝、裂缝、空鼓地面、松动旧环氧的特殊处理

    Special treatment for expansion joints, cracks, hollowing floors and loose old epoxy 

    1、对开裂之部位采用切割片切成V型小槽后,再用高倍中涂砂浆予以修补填平;细小的裂缝可以用环氧树脂加Extender T增稠剂修补;待完全固化后再用手磨机细打至平整。

    1. Cutting slices into V-shaped grooves are used to repair and fill the cracks. Fine cracks can be repaired with epoxy resin and Extender T thickener. Fine cracks can be smoothed by hand grinder after solidification. 

    2、对空鼓、旧环氧松动之部位凿除,如凹糟较深,采用高倍中涂砂浆予以补平,完全固化后再用手磨机细打至平整。

    2. Cut hollow drum and loose parts of old epoxy, such as deep concave, use high-power medium-coated mortar to flatten them, and then grind them fine to flat after solidification. 

    3、所有特殊场地修补处理后,再清洁一遍。

    3. All special sites should be cleaned once again after repair. 

    检验方法:

    Methods of inspection: 

    a、以上部位的处理是整个环氧地坪使用寿命长短的重要一环,不然将导致地坪开裂。

    A. The treatment of the above parts is an important part of the whole service life of the floor, otherwise it will lead to cracking of the floor. 

    b、经处理后,与整个地面相平,修补处无离间、密实,坚硬,平整。

    B, after processing, and the entire ground level, the repair place without separation, dense, hard, smooth. 

    二、环氧底涂

    Two. Epoxy primer 

    1、施工前需确保地

    1. Ensure construction before construction. 

    2、将环氧树脂和固化剂按正确比例混合搅拌,

    2. Mix the epoxy resin and the curing agent in the right proportion. 

    3、搅拌均匀后,采用刮刀或滚筒施涂的方法施涂。

    3. After mixing evenly, apply scraper or roller. 

    4、要求浸透加强附作力。

    4. It is required to soak and strengthen the attachment force. 

    5、待第一遍干固后再施涂环氧中涂层。

    5, after the first dry, the epoxy coating will be applied again. 

    三、环氧中涂层

    Three. Epoxy coating 

    1、施工前需确保地面干净,如有杂物粘附需清除;

    1. Before construction, make sure that the floor is clean. 

    2、将环氧树脂和固化剂按正确比例混合搅拌,并按配比加上一定的石英砂;

    2. Mix the epoxy resin and the curing agent in the right proportion and add a certain amount of quartz sand to the ratio. 

    3、搅拌均匀后倾倒在地面上,使用镘刀按设计的厚度将材料均匀镘开,以增加强度和耐冲击力;使地面更加结实,抗压。

    3. After mixing evenly, dump it on the ground. Use trowel to evenly trowel the material according to the designed thickness, so as to increase the strength and impact resistance, and make the ground stronger and more compressive. 

    4、中涂层干固后,采用打磨,把表面的流挂物、颗粒打磨平整。

    4. After dry coating, the middle coating is ground and smoothed by grinding. 

    5、灰尘处理干净。

    5, dust disposal is clean. 

    检验方法:施工交接处理是否妥当,踢脚线位置平直,与墙壁无离间,平整。

    Inspection method: Whether the construction handover treatment is appropriate, the position of kick line is straight, no separation from the wall, flat. 

    四、环氧腻子层

    Four, epoxy putty layer 

    1、在洁净的地面上,将环氧树脂和石英粉按正确的配比搅拌均匀后,采用批刀均匀镘刮在地面上,以增加中涂与面层之间的结合,并进一步调整地面的平整度;

    1. After mixing the epoxy resin and quartz powder in the right proportion on the clean ground, the batch knife is used to scrape evenly on the ground to increase the combination between the middle coating and the surface layer and further adjust the levelness of the ground. 

    2、视实际需要施工遍数,要求达到平整无孔洞,无批刀印及砂磨印为准。

    2, depending on actual needs, the number of construction is required to achieve smooth, non hole, no batch knife printing and sand grinding. 

    检验方法:使地面完全平整无孔洞,无批刀印及砂磨印方可进行面涂层施工。

    Inspection method: To make the ground completely flat without holes, no batch of knife prints and sanding prints before surface coating construction can be carried out. 

    五、环氧面涂层

    Five. Epoxy coating 

    1、施工前需保持干净,如有杂物粘附需清除;

    1, before construction should be kept clean. 

    2、将面涂材料的B组份先搅拌均匀;再加入固化剂混合,充分搅拌;

    2. First, evenly mix the B components of the surface coating material; then add the curing agent and mix well and stir well. 

    3、使用辊筒将材料均匀涂布;

    3. Use roller to evenly coat the material. 

    4、第一遍涂层干固后,再施工第二次面涂层。

    4. Once the first coating is dry and solid, then the second surface coating is then constructed. 

    5、自流平面涂用镘刀刮镘一遍

    5, self flow flat coated trowel scraping again. 

    6、注意先后施工交接处的处理;涂层要求均匀,无流挂。

    6. Attention should be paid to the treatment of the successively constructed juncture. 

    检验方法:地面色泽均匀、无流挂、无针孔、光洁、平整。

    Test method: uniform color, no hang, no pinhole, smooth and smooth. 


    标签:   环氧地坪 地坪 环氧地坪漆 环氧地坪施工
    无锡环氧地坪 技术支持:【易商科技】