欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 环氧地坪

    如何区分环氧地坪施工与传统地坪刷油漆

    2018-10-19 10:14:53 无锡盛发地坪科技有限公司 阅读

    不少用户觉得环氧地坪施工,即是陆地清扫整理一下,而后直接在上头滚涂一层环氧地坪漆就行了?其实不然!环氧地坪漆施工,绝对不只是陆地刷漆!在本质施工中,正途环氧地坪漆施工与"环氧地坪刷漆"是有很大分别的,越发是基面办理以及施工工艺.

    Many users think that the construction of epoxy floor, that is, land cleaning and finishing, and then directly roll on the top coated with epoxy floor paint on the line? Actually not! Epoxy floor paint construction, not just land painting! In essence, the construction of the right way floor paint and "floor painting" is very different, more and more is the base management and implementation. Workmanship.

    对混凝土陆地的要求:混凝土要求平坦密实,强度要求不低于C20;陆地平坦度通常要求在2M界线内落差不大于2mm;如落差较大,则地坪涂层需加厚以节减落差.

    Requirements for concrete land: concrete is required to be flat and compact, strength requirements are not less than C20; land flatness is usually required to drop within the 2M boundary less than 2 mm; if the drop is large, the floor coating should be thickened to reduce the drop.

    如需涂装的陆地处于地下室等地区,地下水位较高,则混凝土底层应作防水办理;新浇筑混凝土干枯起码三周以上,含水率不高于8%.

    If the land to be coated is in the basement and other areas, the groundwater level is high, the concrete floor should be waterproof; the newly poured concrete dried up for at least three weeks, the moisture content is not higher than 8%.

    基面是悉数地坪名目品质的基本,没有抵达上述准则的陆地,需求实行下面办理:办理目标:升高陆地合座平坦度,去除浮层及污物,取得均一的毛糙表面以利于涂层附着.办理设备:自吸尘陆地磨削机、真空吸尘器等.

    Base surface is the basic quality of all the terrace items, not reaching the above criteria of land, need to implement the following procedures: processing objectives: to increase the flatness of land seats, remove floating layer and dirt, to obtain a uniform rough surface for coating adhesion.

    要求:抵达陆地结实、无砂眼、窝洞,同时要求干枯、干净、无浮尘、油污、水泥砂粒等杂物.工序:选用陆地磨削机合座打磨一遍-吸尽尘埃-修补大的窝洞、凹下及裂痕.关于旧漆陆地,如旧漆层附着不牢,需选用陆地铣刨机合座去除旧漆层(1mm厚度下面旧漆层可选用金刚切削刀办理),因办理本钱高,如顾客不要求合座去除旧漆,则只去除松动旧涂层,去除表面油污及杂物.

    Requirements: Arrive on the land solid, no sand holes, holes, and at the same time dry, clean, no dust, oil, cement sand and other debris. Procedure: Choose land grinding machine seat grinding - dust absorption - repair large holes, dents and cracks. Old paint layer (1 mm thickness below the old paint layer can be used diamond cutter), because of the high cost of handling, if customers do not require seating to remove old paint, only remove loose old coating, remove surface oil and debris.


    标签:   环氧地坪 环氧地坪漆 环氧地坪施工 地坪
    无锡环氧地坪 技术支持:【易商科技】