欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 地坪知识

    水泥地面硬化剂的施工工艺是怎样的

    2018-10-19 10:00:20 无锡盛发地坪科技有限公司 阅读

    现在很多仓库,厂房都有使用水泥地面硬化剂,即耐磨有容易清洁,深受消费者们的喜欢,水泥地面硬化剂的使用量也越来越多,那么水泥地面硬化剂的施工工艺是怎样的呢?下面小编给大家详细介绍下,一起来看看吧。

    Now many warehouses, factories have the use of cement ground hardener, that is, wear-resistant and easy to clean, deeply loved by consumers, the use of cement ground hardener is also increasing, then cement ground hardening agent construction technology is what? The following small to everyone in detail, together with a look at it.

    1、表面处理

    1. Surface treatment

    去除表面漆层,清扫,磨去表面污染,涂层、清洁地面并晾干

    Remove surface paint, clean, remove surface contamination, coat, clean the floor and dry.

    2、3浸泡

    2, 3 soak

    表面处理后清洗、晾干,把本材料浸泡在混凝土表面,使其表面浸湿、饱和。此外,也可直接把本材料倒在混凝土的表面,然后用软塑料扫把推开的扫平的方法施工。请注意:本产品是渗透液不是涂膜,只有当它在混凝土表面上的分布量足够时,才能充分往内里渗入。其分布量足够的判断依据是:浸满表面,可用软扫把来回扫动,加速往内里渗入。

    After surface treatment, the material is washed and dried. The material is soaked in the concrete surface to make the surface wet and saturated. In addition, the material can also be poured directly on the surface of concrete, and then the method of sweeping away with a soft plastic broom is used for construction. Please note: this product is a permeate, not a coating, only when it is distributed on the surface of concrete enough to fully infiltrate the inside. Its distribution is sufficient to judge the basis is: immersed in the surface, you can use a soft broom to sweep back and forth, accelerate infiltration into the inside.

    用本产品浸湿混凝土表面的时间至少要持续30分钟。等待浸泡在表面上的本材料变粘,并达到用脚踩踏时有类似凝胶质的粘滑感。在严寒或完全无风的条件下,这个变粘滑过程约需一个小时或更长的时间才完成,但在炎热或刮风环境下,这一过程所需的时间将缩短,甚至只需要15分钟。在非常炎热的情况下,若在30分钟内即已完成这个变粘滑、呈凝胶状的过程。本材料的浸层变粘滑后,在其表面上喷水雾。可用低喷雾器具或带喷咀的软管(应将喷咀调节至喷雾状态)喷洒水。水能使本材料产生再溶作用,接着用磨机加磨片在上面抛磨浸泡层,以促进本材料的再次渗入。随后吸干。

    Wetting the concrete surface with this product lasts for at least 30 minutes. Waiting for the material to become sticky when soaked on the surface, and to have a slippery, gelatinous feel when trampled. The process takes about an hour or more to complete in cold or completely windless conditions, but in hot or windy conditions it takes even 15 minutes to complete. In very hot conditions, the process of becoming sticky, slippery and gelatinous has been completed within 30 minutes. The impregnated layer of this material is sticky and slippery, and water mist is sprayed on its surface. Use low spray equipment or hose with nozzle (spray nozzle should be adjusted to spray state) to spray water. Water can cause the material to dissolve again, and then grind the immersion layer on it with a mill and a grinding disc to promote the material to infiltrate again. Then dry.

    4、抛光

    4, polishing

    用拖把材料均匀地拖在地面上,然后用黑垫对浸好的地面进行抛光处理,交付使用。

    Drag the material evenly on the ground with a mop, and then polish the soaked ground with a black pad for delivery.

    注意事项

    Matters needing attention

    1、如新地面需要色彩,可先施工彩色水泥,金刚砂或水磨石,再进行硬化剂处理。

    1. If the new ground needs color, can first construct color cement, diamond or terrazzo, and then hardener treatment.

    2、浸泡硬化剂前,须等地面充分干燥,方能达到预期的效果

    2. Before the sclerosing agent is soaked, it is necessary to wait until the ground is dry enough to achieve the desired effect.

    3、施工温度:不低于5℃,不高于45℃。

    3. Construction temperature: no less than 5 C, not higher than 45 C.


    标签:   环氧地坪 环氧地坪施工 地坪 环氧地坪漆
    无锡环氧地坪 技术支持:【易商科技】