欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 环氧地坪

    厂家讲解环氧地坪涂层批刮工艺的要点

    2018-10-18 21:56:10 无锡盛发地坪科技有限公司 阅读

    环氧地坪因其高强度、耐磨损等优异的性能,被人们广泛运用。环氧地坪的的涂层批刮是环氧地坪施工中的关键部分。批刮中涂层要充分考虑到地面最终成型的效果,这就需要从选用石英砂、打磨、选材料等方面注意。首先,我们要知道环氧树脂地坪批刮施工的目的是什么?

    Epoxy floor is widely used because of its excellent performance such as high strength and wear resistance. The coating scraping on epoxy floor is a key part in the construction of epoxy floor. In batch scraping, the final forming effect of the ground should be fully considered, which requires attention from the selection of quartz sand, grinding, material selection and other aspects. First of all, we need to know what the purpose of epoxy resin floor batching is. 

    ①增厚,树脂涂层要达到用户要求的厚度,达到设计要求,满足载重需求;

    1. Thickening, resin coating to meet the thickness of user requirements, meet design requirements, meet load requirements;

    ②整型,通过涂层的批刮填补环氧地坪的坑洼,使地面最终完成效果达到最优。

    (2) integer, fill the floor potholes by scraping the coating to make the ground finish the best.

    第二、环氧地坪的中涂批刮层需要进行多道批刮,并且每道批刮固化后往往需要进行打磨,这关系到下道工序的质量。

    Secondly, the middle coat scraping layer of epoxy floor needs to be scraped in many batches, and each batch of scraping often needs to be polished after curing, which is related to the quality of the next process.

    第三、涂层批刮层的打磨作业,传统上一般都使用角向磨光机或者稍大型的打磨设备如常用的K30。

    Thirdly, the coating batch scraper grinding operations, traditionally using angle grinder or slightly larger grinding equipment such as the commonly used K30.

    磨光机的使用对环氧地坪的质量有很重要的作用,所以在使用磨光机的时候要注意避免下边这些问题:

    The use of the polisher plays an important role in the quality of the epoxy floor, so when using the polisher, attention should be paid to avoid the following problems:

    在施工过程中,操作的工人进行下蹲式工作,劳动强度大而工作效率低;

    During the construction process, the workers worked squatting, with great labor intensity and low work efficiency.

    因为角向磨光机在施工过程中很难与吸尘设备连接,所以在施工过程中灰尘较大,对工人的健康有很大的危害;

    Because it is difficult to connect angular grinder with vacuum cleaning equipment during construction, the dust in the construction process is large, which is harmful to workers'health.

    由于角向磨光机使用的是串激式电机,负荷能力较差,在磨削时往往不能承受住与地面接触的压力,容易电流过大,造成电机的损坏

    Because the angle grinder uses series motor, the load capacity is poor, often can not withstand the ground contact pressure in grinding, easy to excessive current, resulting in damage to the motor.

    人工操作角向磨光机对地面进行磨削时,磨片与地面大多是局部接触,这样容易造成磨片受力不均,损坏过快,砂盘磨片的消耗量大的情况。

    When grinding the ground with manual angular grinder, the grinding disc and the ground are mostly in local contact, which is easy to cause uneven force on the grinding disc, damage too fast, and large consumption of the grinding disc.

    针对这种情况,一些施工人员设法在地面磨削机上安装砂磨片,对中涂批刮进行打磨。这不仅解决了上述的问题,而且也提高了工作的效率。

    In view of this situation, some construction personnel try to install sand grinding discs on ground grinders to grind the middle coating scrape. This not only solves the above problems, but also improves the efficiency of the work.

    第四、用树脂砂浆搅拌机将树脂砂浆搅拌均匀,将搅拌好的树脂砂浆用摊铺机按顾客要求的厚度摊于素地表面,然后再用抹平机抹平。通常砂浆的批刮会进行一到两遍,根据现场施工地面情况和设计厚度选用合适目数的石英砂,这样做出来的地面效果好,成本适当。

    Fourthly, the resin mortar is stirred evenly by the resin mortar mixer, and the resin mortar is spread out on the plain surface by the paver according to the thickness required by the customer, and then smoothed by the plaster. Usually the scraping of mortar will be done one or two times, according to the site construction ground conditions and design thickness to select the appropriate number of quartz sand, so that the ground effect is good, the cost is appropriate.

    作为环氧环氧地坪施工中重要一环的涂层批刮环节,只有把握好它的每一步,才能确保环氧地坪的质量,使顾客满意!

    As an important link in the construction of epoxy floors, the quality of epoxy floors can be guaranteed and the customers can be satisfied only by grasping every step of the process.



    标签:   环氧地坪 地坪 环氧地坪漆 环氧地坪施工
    无锡环氧地坪 技术支持:【易商科技】