欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 常见问题

    厂家解读环氧地坪失去光泽的原因和解决办法

    2018-10-18 21:49:32 无锡盛发地坪科技有限公司 阅读

    我们都知道,越平整光线反射越强,光泽度越好,如果固化环氧地坪完工后不平整,光泽度一般都不会太好,这就要求我们在基面处理的时候一定要先将环氧地坪。 打磨平整,平整的地面不但有利于固化剂材料的均匀渗透,也能让固化环氧地坪的整体效果更佳。

    As we all know, the smoother the light reflects, the better the glossiness. If the cured floor is not smooth after completion, the glossiness is generally not very good, which requires us to treat the epoxy floor first. Grinding flat, flat ground is not only conducive to the uniform penetration of curing agent materials, but also make the overall effect of the curing floor better. 

    固化地坪施工打磨不均匀

    Uneven construction of solidified floor construction 

    打磨作为固化地坪最为重要的一个环节,我们在施工过程中一定不能马虎,严格按照厂家制定的标准施工流程来执行,横向竖向交叉打磨,不少磨漏磨。

    As one of the most important links of the solidified floor, we must not be careless in the construction process, strictly in accordance with the standard construction process formulated by the manufacturer to carry out, horizontal and vertical cross-grinding, a lot of abrasion. 

    固化剂材料用量不够

    The amount of curing agent is not enough. 

    固化剂的使用剂量一定要符合工艺要求,施工单位不要为了节约材料成本而压缩整个工程的质量。

    The dosage of curing agent must meet the technological requirements, and construction units should not compress the quality of the whole project in order to save material costs. 

    刚做好的环氧地坪经常会因为表面出现一些瑕疵而影响地坪的整体效果,像有些环氧地坪因施工不当,刚喷涂完的涂层表面就会呈现乳白色,像云一样变白而且黯淡无光,不但影响其外观,甚至降低了其使用性能,那么造成这个问题的主要原因是什么呢?美地宝给大家分享失去光泽度的四大原因及四大措施。

    Fresh epoxy floors are often affected by surface defects, such as some epoxy floors due to improper construction, just sprayed coating surface will appear Milky white, cloudy white and dull, not only affect its appearance, and even reduce its performance, then cause this What is the main reason for this problem? Mei Di Bao to share with you four reasons for losing gloss and four major measures. 

    上海博歌-环氧地坪

    Shanghai Bo Ge epoxy floor 

    上海博歌-环氧地坪

    Shanghai Bo Ge epoxy floor 

    环氧地坪失去光泽的原因

    Reasons for losing gloss of epoxy floor 

    1、湿度过高。在进行地面喷涂的时候由于地面湿度过高,导致其表面呈现乳白色色块。

    1. Humidity is too high. When the surface spraying is carried out, the surface humidity is too high, which causes the surface of the surface to appear milky white. 

    2、稀释剂质量不合格。所使用的稀释剂的品质不良,挥发太快。

    2. The quality of the diluent is not qualified. The diluent used is of poor quality and volatilization too fast. 

    3、喷涂场所气温过低。尤其是在被喷涂的物体温度低于室温的时候。

    3, the temperature of the spraying place is too low. Especially when the temperature of the object being sprayed is lower than that at room temperature. 

    4、喷涂室的空气不流通,又缺乏加热设备时也会导致这一情况。

    4, the air in the spray room is not circulated, and the lack of heating equipment will also lead to this situation. 

    环氧地坪失去光泽的预防措施

    Preventive measures for losing gloss of epoxy floor 

    1、在进行地坪漆施工时,要进行适当加热,升高喷涂环境室温。

    1. During the construction of floor paint, proper heating should be carried out to raise the ambient temperature of spraying. 

    2、使用品质良好的稀释剂,使用挥发较慢的稀释剂。

    2, use good quality diluent, use slower volatile diluent. 

    3、在稀释剂内添加防潮剂,使用量药效,否则会减慢干燥速度。

    3. Add moisture-proof agent in diluent, use amount of efficacy, otherwise it will slow down drying speed. 

    4、涂装前使被喷涂的物体高于环境室温10摄氏度左右。

    4, before painting, the object being sprayed is higher than ambient temperature at 10 degrees Celsius. 


    标签:   环氧地坪 地坪 环氧地坪漆 环氧地坪施工
    无锡环氧地坪 技术支持:【易商科技】