无锡环氧地坪近些年被广泛用于医院、车间等，是比较受欢迎的环氧地坪。环氧地坪施工质量常见缺陷有几大方面？ 1、环氧地坪在施工过程中出现“花脸”，也就是环氧地坪色彩不均： 产生这种缺陷的原因有二点：第一，颜料搅拌不均。第二面层受到其它有色液体污染。颜料搅拌必须专人负责，做到计量准确。不能心估目测，另外，不能一边加水，一边倒颜料。这样做会使颜料结块，局部色彩偏重。须坚持颜料与水泥干拌均匀后再加水、加石碴的办法，使颜料分散均匀。面层受污染，应及时清理干净。最根本的办法还是加强管理，如若地面篱工完毕，其它工程仍在交叉施工，最好在面层上部铺一层保护材料，免受污染及碰损。
In recent years, Wuxi epoxy floor has been widely used in hospitals, workshops, etc. It is a popular floor. What are the common defects in the construction quality of epoxy floor? 1. There are two reasons for the uneven color of the epoxy floor: first, uneven mixing of pigments. The second surface layer is contaminated by other colored liquids. Pigment mixing must be handled by a dedicated person to achieve accurate measurement. We can't estimate by heart or by eyes. In addition, we can't add water and pour paint at the same time. Doing so will agglomerate the pigments and give them partial color. It is necessary to adhere to the method of adding water and ballast after dry mixing of pigments and cement to make the pigments disperse evenly. If the surface is polluted, it should be cleaned up in time. The most fundamental way is to strengthen management. If the ground fence is completed and other projects are still under cross-construction, it is better to lay a protective material on the top of the surface layer to avoid pollution and damage.
2. The unevenness of epoxy floor
The uneven exposure of stones has the following main effects: when there are footprints on the surface, if not handled in time, there will be a slight subsidence at the footprints. In addition, if the foot is stepped on a soft surface, the stone at the footprint will sink and the upper part of the cement slurry will increase. When polished, the footprints sink slightly, affecting polishing. So the stones on the surface are not uniform and clear enough. In the face of this phenomenon, operators should arrange the construction procedures, and try to avoid a large number of interpenetration on the plastered surface. In addition, the construction should try to wear flat-soled rubber shoes, do not wear high heels or more obvious corrugated rubber shoes.
3. Empty Drum on Construction Ground of Epoxy Floor
Empty drum is mainly manifested in: A. The bond between the surface layer and the base layer is not strong, resulting in empty drum. B. The bond between the surface layer and the leveling layer is not strong, resulting in empty drum. The main reason is that the grass-roots cleaning is not enough, such as dust, debris and other additives, will affect the bonding between the two layers. It can be seen that the cleaning of the grass-roots is the key factor affecting the bonding. Surface empty drum needs to be handled in time, especially in large areas with cracks, otherwise the service life of the floor will be greatly affected. When dealing with empty drum problems in floor construction, attention should be paid to keeping the repaired color as consistent as possible with the original ground color. When repairing, make the size of the back patch as regular as possible. If the epoxy self-leveling can be repaired in a grid, the effect will be better.
标签:  地坪 地坪 环氧地坪施工 无锡环氧地坪 地坪施工