欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 地坪知识

    环氧地坪施工对于环境有哪些具体施工标准要求

    2019-08-30 10:22:48 无锡盛发地坪科技有限公司 阅读

    如今人们对于房屋的装修真的是越来越看重了呢,而且这些也都还是精装。不知大家都是都知道环氧地坪呢,其实环氧地坪的特点真的有很多,如高强度、耐磨损、美观的地板,具有无接缝、质地坚实、防腐、防尘等优点。那么选择环氧地坪施工对于环境有哪些要求呢。

    Nowadays people are really paying more and more attention to the decoration of houses, and these are also hardcover. I don't know that everyone knows about epoxy flooring. In fact, there are many characteristics of epoxy flooring, such as high strength, wear resistance, beautiful flooring, with seamless, solid texture, anti-corrosion, dust and other advantages. So what are the requirements for the environment when choosing epoxy floor construction? 

    1、硬度

    1. Hardness

    硬度是指涂装基面的强度或混凝土基面的标号。 涂装基面的硬度从根本上决定涂层的使用年限、涂层的附着力和涂层使用效果。

    Hardness refers to the strength of the coated base or the label of the concrete base. The hardness of the coating base fundamentally determines the service life of the coating, the adhesion of the coating and the application effect of the coating.

    2、平整度

    2. Flatness

    平整度是指涂装基面平整与否的关键指标。 基面的平整度从根本上决定涂层的平整度,涂层的平整度直接影响到涂层的使用效果。

    Flatness refers to the key index of coating base surface flatness or not. The smoothness of the base surface fundamentally determines the smoothness of the coating. The smoothness of the coating directly affects the application effect of the coating.

    3、厚度

    3. Thickness

    厚度是指涂装基面(结构层)最面上一层混凝土的厚度,不是指整个基层的厚度。厚度太薄,则容易脱层、空鼓。 要求面层的结构层的最小厚度为5CM的硬度C25以上。

    Thickness refers to the thickness of the concrete layer on the most surface of the coated base (structural layer), not the thickness of the whole base. If the thickness is too thin, it is easy to delaminate and empty. The minimum thickness of the structural layer of the surface layer is required to be more than 5 CM hardness C25.

    4、湿度

    4. Humidity

    湿度是指涂装基面的含水率和涂装环境的空气湿度。 不同环氧地坪涂料对涂装基面含水率要求不一致,环氧树脂地坪涂料要求8%以下,甲基丙烯酸甲酯树脂要求10%左右。 基面的含水率超标,则可能涂层出现水泡、起鼓、整片脱落等现象。 空气中的含水率即湿度,可以用湿度计测量,一般环氧地坪漆施工时最好湿度在85%以下,但不要低于30% 。

    Humidity refers to the moisture content of the base surface and the air humidity of the coating environment. Different floor coatings have different requirements for the moisture content of the base surface. Epoxy floor coatings require less than 8% and methyl methacrylate resin requires about 10%. If the moisture content of the base surface exceeds the standard, blisters, bulging and falling off of the whole coating may occur. The moisture content in the air is humidity, which can be measured by hygrometer. Generally, the best humidity for epoxy floor paint construction is below 85%, but not below 30%.

    5、温度

    5. Temperature

    温度是指涂装环境的温度,可以用温度计测量。 不同种类的环氧地坪涂料对温度的要求是不一致的。环氧要求在5℃以上,当然温度太高也不能施工。,一者危险,二则固化太快不利于涂层性能展现。

    Temperature refers to the temperature of the coating environment, which can be measured by a thermometer. Different kinds of floor coatings have different requirements for temperature. The epoxy requirement is above 5 Celsius, of course, the temperature is too high to be constructed. One is dangerous, the other is that too fast curing is not conducive to the performance of the coating.

    6、洁净度

    6. Cleanliness

    洁净度是指除涂装地坪涂料之外再无其他涂料或杂物包括灰尘、油污、水泥残渣、其他油漆等。

    Cleanliness refers to the absence of other coatings or sundries, including dust, oil, cement residues, other paints, etc., except for floor coatings.

    7、通风度

    7. Ventilation

    通风度,是涂装环境通风与否的指标等 。 因双组份或多组分的地坪涂料固化时会产生热量和水气必须及时由流动空气带走,所以要求涂装环境相对通风,但也不能太过通风。

    Ventilation is an indicator of ventilation in painting environment. Because the heat and moisture generated when two or more components of floor coating solidify must be taken away by the flowing air in time, the painting environment is required to be relatively ventilated, but not too ventilated.

    8、粗糙度

    8. Roughness

    粗糙度,是指涂装基面的表面的较小间距和微小峰谷的不平度。 地面基面的两波峰或波谷之间的局距离(波距)很小要求1mm以下。它属于几何形状误差。基面的粗糙度越小,则表面越光滑,涂层与基面的接触面积比也就越小,涂层的附着力也会下降,反之则涂层的附着力将提高。

    Roughness refers to the small spacing of the surface of the base surface and the unevenness of the small peaks and valleys. The local distance (wave distance) between the two peaks or troughs on the ground surface is very small, which requires less than 1 mm. It belongs to geometric error. The smaller the roughness of the base surface is, the smoother the surface is, the smaller the contact area ratio between the coating and the base surface is, and the adhesion of the coating will also decrease, otherwise the adhesion of the coating will increase.


    标签:   环氧地坪 地坪 环氧地坪漆 环氧地坪施工 无锡环氧地坪 环氧地坪翻新
    无锡环氧地坪 技术支持:【易商科技】