欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 地坪知识

    环氧地坪的圆弧角的处理方法以及基层处理须知

    2019-08-03 16:39:05 无锡盛发地坪科技有限公司 阅读

    环氧地坪在施工前和过程中常常会遇到各种问题,其中圆弧角与基层处理都相当重要,并且存在着一定难度。那么,当我们遇到圆弧角又该怎么处理呢?基层处理的处理又有哪些需要注意的地方呢?以下关于“环氧地坪的圆弧角的处理方法以及基层处理须知”的介绍。在环氧地坪施工中的要求许多,尤其是圆弧角这种难处理的当地,是环氧地坪施工人员有必要关注的问题。下面为我们介绍一下,环氧地坪圆弧角施工时应该怎么处理。

    Epoxy floor often encounters various problems before and during construction, among which arc angle and base treatment are very important and difficult. So what should we do when we encounter an arc? What should we pay attention to when dealing with grass-roots treatment? Following is an introduction to the "Processing Method of Arc Angle of Epoxy Floor and Basic Processing Notes". There are many requirements in the construction of epoxy flooring, especially the arc angle, which is difficult to deal with, which is a necessary concern for the floor constructors. Here is how to deal with the construction of arc angle of epoxy floor. 1、首先把要做圆弧角的地轨墙角彩钢板及周边地上清扫洁净,整理尘埃,修补凹坑等。

    1. First of all, it is necessary to clean up the colored steel plate of the arc corner of the rail wall and the surrounding ground, tidy up the dust, repair the pits and so on.

    2、保证圆弧角地轨墙角无尘埃后,贴好美纹纸,刷上底涂,底涂切忌弄到墙板上,底涂后把拌和均匀的环氧干砂浆均匀地倒在地轨边上,用圆弧刀进行圆弧角模型施工,施工工程中圆弧刀面需经常用松香水或者稀释剂清洗,坚持环氧砂浆圆弧边和彩钢板边平坦共同,不得高于彩钢板,做好模型之后及时撕掉美纹纸。

    2, ensure that the circular corner of the corner of the wall without dust, embossed fine paper, brush the bottom coat, bottom coat should not be allowed to get on the wall board, after the bottom of the coating evenly mixed dry epoxy mortar evenly poured on the edge of the rail, circular arc cutter circular arc model construction, the construction engineering arc knife face often need to use pine perfume or diluent cleaning. Hold the epoxy mortar arc edge and color steel plate edge flat common, not higher than the color steel plate, after making the model, tear off the American paper in time.

    3、环氧砂浆圆弧固化后用120目左右的砂纸打磨圆弧角,坚持顺滑,后贴美纹纸,批环氧腻子;接着用150目左右的砂纸打磨腻子,重复批腻子打磨操作,直至打磨的圆弧角平坦度及光滑度达标。

    3. After curing, epoxy mortar arc is polished with 120 mesh sand paper, adhere to smoothness, paste beautify paper and batch epoxy putty; then polish putty with 150 mesh sand paper, repeat batch putty polishing operation until the flatness and smoothness of the arc angle are up to the standard.

    4、贴好美纹纸,和地上一同上面涂环氧配比不能出差错,每道工序需比及涂料干透后才干进行下一道,每道工序施工后需及时整理洁净,保证没有尘埃,上面涂之前圆弧角的下口与地上触摸应平坦。

    4. Stick fine-grained paper and coat epoxy on the same surface as on the ground. Each process needs to be compared with the paint before drying. After each process construction, it needs to be cleaned up in time to ensure that there is no dust. The lower part of the arc angle before coating should be flat with the touch on the ground.

    环氧地坪基层处理有哪些注意事项

    [What precautions should be taken in the treatment of epoxy flooring grass-roots units]

    施工所有环氧环氧地坪前,首先需要进行基层处理,基层处理的好坏是十分重要的,关系着后期环氧地坪漆的施工难度与质量。这里小编为您简单介绍下地坪基层处理的工艺及注意事项。

    Prior to the construction of all epoxy floors, the basic treatment is necessary. The quality of the basic treatment is very important, which is related to the difficulty and quality of the construction of epoxy flooring paint in the later period. Here, Xiaobian gives you a brief introduction of the process and precautions for the treatment of the lower floor.

    环氧地坪对于基层的硬度有一定的要求,要求混凝土达到C25及以上的强度,否则很影响环氧地坪系统的质量。如果是新浇混凝土,混凝土地坪基面在浇筑时同时进行混凝土原浆收光,可保证后期环氧树脂工业地坪漆实施的成本经济和质量优良。

    Epoxy flooring has certain requirements for the hardness of the base, requiring concrete to reach C25 and above strength, otherwise it will affect the quality of epoxy flooring system. If it is newly poured concrete, the base of the concrete floor is lightened by the original concrete slurry at the same time, which can ensure the cost-effectiveness and quality of the epoxy resin industrial floor paint in the later period.

    其养护期不得低于4周,必须等混凝土强度形成后,再进行打磨等处理。打磨一定要把基面上的油污及浮尘等赃物去除干净,并彻底做好吸尘工作,以便环氧树脂层与基面完全结合。如果混凝土表面较难清理,可以采用酸洗发,利用盐酸对地面进行处理,等盐酸反应完全后,不再有气泡产生,再用清洗干净。

    The curing period should not be less than 4 weeks. After the strength of concrete is formed, it must be grinded and treated. The oil and dust on the base surface must be removed and the dust should be cleaned thoroughly, so that the epoxy resin layer and the base can be fully combined. If the surface of concrete is difficult to clean, acid shampoo can be used to treat the ground with hydrochloric acid. After hydrochloric acid reaction is complete, no bubbles will be generated, and then clean.

    另外由于环氧地坪对于地面的含水率要求很高,所以施工环氧地坪前,必须保证地面的含水率不超过4%,可以通过通风、使用鼓风机、太阳灯等烘干地面。严格保证地面干净、密实。

    In addition, because the epoxy floor requires a high water content of the ground, it is necessary to ensure that the water content of the ground does not exceed 4% before the construction of the epoxy floor. The ground can be dried by ventilation, using blowers, solar lamps, etc. Strictly ensure that the ground is clean and compact.


    标签:   环氧地坪 地坪 环氧地坪漆 环氧地坪施工 地坪施工 无锡环氧地坪
    无锡环氧地坪 技术支持:【易商科技】