欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 地坪知识

    环氧地坪施工前打磨地面需要注意的地方

    2019-05-11 14:26:47 无锡盛发地坪科技有限公司 阅读

    前面给大家介绍了环氧地坪漆施工前打磨地面的目的,知道对基础地面打磨是环氧地坪漆施工工艺中非常重要的一个步骤,直接影响到环氧地坪漆的施工效果,下面环氧地坪漆厂家给大家讲解环氧地坪漆施工前打磨地面需要注意的地方。环氧地坪漆在施工前将地面充分磨平、棉掉,这样可以减少用漆量,增加附着力,使漆膜不易破坏,并使整体效果看上去更平整、美观。环氧地坪漆施工前打磨地面对新建水泥地坪上面的水泥块,灰粉起到很好的去除作用,能有效地打开水泥毛孔,以便环氧树脂底漆更好地渗透渗出与吸收,环氧地坪漆工程的质量起到至关重要的作用。

    The purpose of ground polishing before construction is introduced. It is known that ground polishing is a very important step in the construction process of epoxy floor paint, which directly affects the construction effect of epoxy floor paint. The following epoxy floor paint manufacturers explain to you the points needing attention before construction. Before construction, the epoxy floor paint will be fully polished and cotton removed, which can reduce the amount of paint used, increase adhesion, make the film not easy to damage, and make the overall effect look smoother and more beautiful. Before the construction of epoxy floor paint, the ground is polished to remove the cement blocks and powders on the newly built cement floor, which can effectively open the cement pore, so that the epoxy resin primer can penetrate and absorb better, and the quality of the epoxy floor paint project plays a vital role. 1、基础地面打磨之前应初步清扫地面上的灰尘垃圾,如果现场有机器设备,应通知业主将其转移或者包裹好,避免打磨时灰尘对机器设备造成损害;

    1. Dust and garbage on the ground should be preliminarily cleaned before grinding the foundation ground. If there are machinery and equipment on the ground, the owner should be notified to transfer or wrap it up so as to avoid damage to the machinery and equipment caused by dust during grinding.

    2、用2米靠尺初步检查地面平整度,对影响平整度的部位进行明显标识;

    2. Preliminary inspection of ground roughness with a 2-meter gauge, and marked the parts that affect the roughness.

    3、已有沥青的伸缩缝(参考《环氧地坪漆施工前伸缩缝处理方法》),合同上无特别要求时,只要将沥青割至低于地面一毫米即可,以防打磨时将沥青带到其他地方而导致漆面变黄;若有特别要求时,则应将伸缩缝里的东西彻底清除干净;

    3. Expansion joints of existing asphalt (refer to "Processing Method of Expansion Joints before Construction of Epoxy Floor Paint"). If there is no special requirement in the contract, just cut the asphalt below the ground one millimeter, in order to prevent the asphalt from being brought to other places when polishing, which will lead to the paint surface yellowing; if there are special requirements, the things in the expansion joint should be thoroughly cleaned up;

    4、无尘打磨机进行地面打磨时,特别是对做了标识的部位要仔细,打磨机行走速度以平均10-15 米/分钟为宜;

    4. When the dust-free grinder grinds the ground, especially the marked parts, it should be careful. The average walking speed of the grinder should be 10-15 meters per minute.

    5、喷砂机处理地面时应先用无尘打磨机将高出部位进行打磨,平整度基本达到要求后再统一喷砂处理,这样喷砂机可基本均速行驶,具体速度要根据地面强度及喷砂效果而定;

    5. When dealing with the ground, the sand blasting machine should first use a dust-free grinding machine to grind the high parts, and then uniform sand blasting treatment after the roughness basically meets the requirements, so that the sand blasting machine can run at a basic average speed, and the specific speed depends on the strength of the ground and the effect of sand blasting.

    6、检查油渍、水痕、沥青、水泥疙瘩、乳胶漆、水泥浮灰等,洁净度要求是否达标;

    6. Check oil stains, water marks, asphalt, cement knots, latex paint, cement fly ash, etc. to see if the cleanliness requirements meet the standards.

    7、涂装前地面处理达标后方可进行底漆涂装;

    7. Primer painting can be carried out only after the ground treatment reaches the standard before painting.

    8、对于墙角、设备边上或无尘打磨机够不着的地方,则用手动打磨机进行处理,并吸尘,但不能碰坏墙壁及设备;

    8. For corners, edges of equipment or areas beyond the reach of dust-free grinders, the manual grinder is used to process and dust, but the walls and equipment can not be damaged;

    9、再次检查平整度,对局部达不到要求的地方继续打磨,直到平整度符合要求(2m靠尺不大于3mm)。

    9. Check the smoothness again and continue to grind the parts that do not meet the requirements until the smoothness meets the requirements (2m footage is not more than 3mm).


    标签:   地坪 环氧地坪 环氧地坪漆 环氧地坪施工
    无锡环氧地坪 技术支持:【易商科技】