欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 地坪知识

    环氧地坪圆弧角施工时应该如何处理

    2019-02-26 10:58:39 无锡盛发地坪科技有限公司 阅读

    现在环氧地坪因为有很多优点已经被人们广泛采用,但是在环氧地坪施工时,特别是圆弧角地面,有很多地方是需要大家注意的,那么,今天就给大家讲讲环氧地坪圆弧角施工时应该如何处理。1、首先把要做圆弧角的地轨墙角彩钢板及周边地上清扫洁净,整理尘埃,修补凹坑等。

    Nowadays, epoxy flooring has been widely used because of its many advantages, but in the construction of epoxy flooring, especially the arc angle ground, there are many places that need our attention. So, today I will tell you how to deal with the construction of the arc angle of epoxy flooring. 1. First of all, it is necessary to clean up the colored steel plate of the arc corner of the rail wall and the surrounding ground, tidy up the dust, repair the pits and so on. 2、保证圆弧角地轨墙角无尘埃后,贴好美纹纸,刷上底涂,底涂切忌弄到墙板上,底涂后把拌和均匀的环氧干砂浆均匀地倒在地轨边上,用圆弧刀进行圆弧角模型施工,施工工程中圆弧刀面需经常用松香水或者稀释剂清洗,坚持环氧砂浆圆弧边和彩钢板边平坦共同,不得高于彩钢板,做好模型之后及时撕掉美纹纸。

    2, ensure that the circular corner of the corner of the wall without dust, paste beautiful paper, brush the bottom coat, bottom coat should not be made to the wall panels, after the bottom of the evenly mixed dry epoxy mortar evenly poured on the edge of the rail, circular arc cutter circular arc model construction, the construction of arc knife face often need to use pine perfume or diluent cleaning, adhere to the epoxy mortar rim and color steel plate side flat. Similarly, it should not be higher than the color steel plate, tear off the paper in time after making the model.

    3、环氧砂浆圆弧固化后用120目左右的砂纸打磨圆弧角,坚持顺滑,后贴黄色美纹纸,批环氧腻子;接着用150目左右的砂纸打磨腻子,重复批腻子打磨操作,直至打磨的圆弧角平坦度及光滑度达标。

    3. After curing the arc of epoxy mortar, the arc angle is polished with 120 mesh sand paper, and the arc angle is smoothly adhered to, followed by yellow paper and batch of epoxy putty; then the putty is polished with 150 mesh sand paper, and the batch putty polishing operation is repeated until the flatness and smoothness of the arc angle are up to the standard.

    4、贴好美纹纸,和地上一同上面涂环氧配比不能出差错,每道工序需比及涂料干透后才干进行下一道,每道工序施工后需及时整理洁净,保证没有尘埃,上面涂之前圆弧角的下口与地上触摸应平坦。

    4. Stick fine-grained paper and coat epoxy on the same surface as on the ground. Every process needs to be compared with the paint before drying. After each process construction, it needs to be cleaned up in time to ensure no dust. The lower part of the arc angle before coating should be flat with the touch on the ground.



    标签:   地坪 环氧地坪 环氧地坪漆 环氧地坪施工
    无锡环氧地坪 技术支持:【易商科技】