欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 新闻资讯

    生物质热风炉怎么不能自动传送

    2018-11-22 15:35:31 无锡盛发地坪科技有限公司 阅读

    生物质热风炉怎么不能自动传送?1.生物质热风炉穿带不正确。打开右门,按照说明书标明成都收账“穿带过程法”或穿带示意图,正确穿带。2.生物质热风炉送带长度控制成都找人公司电位器在零位。送带长度控制电位器在前面板开关牌上左起第二个位置。顺时针方向调整,则出带长度长反之则短;如果在零位置则不出带。

    How can the biomass hot stove not be transmitted automatically? 1. the wearing of biomass hot stove is incorrect. Open the right door and wear the belt correctly according to the instructions of the tape or the sketch map. 2. the potentiometer of the length control of biomass hot blast stove is zero. The belt length control potentiometer is left in second positions on the front panel switch board. If the clockwise direction is adjusted, the length of the strip will be long and vice versa; if it is in the zero position, it will not be taken out.

    3.选用成都收账PP带太厚或太薄。

    3. the PP belt is too thick or too thin.

    因PP打包带生产厂家有很多,厚度也不一致,应按要求选用;如不可能请按照说明书第十页之方法,仔细调整送退带滚轮之间隙。

    Because PP packing belt manufacturers have many, thickness is not the same, should be selected according to the requirements; if not possible, please follow the method of page 10 of the instructions, carefully adjust the gap between the feeding and returning rollers.

    4.上下分机内有异物。

    4. there are foreign objects in the extension.

    生物质热风炉器长期使用,又未能及时清洁与保养,致使机器内积有赃物,使送带不顺畅自如,应多作清洁保养。

    The long-term use of biomass hot-blast stove fails to be cleaned and maintained in time, resulting in the accumulation of stolen goods in the machine, which makes the delivery not smooth and comfortable, and should be cleaned and maintained more.

    5.送带滚轮间隙不正确。

    5. the belt gap is incorrect.

    一对半自动生物质热风炉送带滚轮之间收账间隙大小对正常送带至关重要,间隙成都找人公司调整参照说明书第10页之说明。仔细调整,调至送带滚轮间隙只比带子厚度多出0.05~1mm时即可。

    The clearance between the feeding rollers of a pair of semi-automatic biomass hot blast stoves is very important for normal feeding. The adjustment of the clearance refers to the instructions on page 10 of the manual. Carefully adjust, transfer to the belt roller clearance only more than the thickness of the belt 0.05~1mm.

    6.电磁铁工作不正常。

    6. electromagnet work is not normal.

    电磁铁不工作。首先检查电磁铁连线焊接头是否脱落,再检查线圈是否烧坏。如两者都无异常,应检查电磁铁是否位移,或是被赃物堵住,使子弹头不能活动自如.

    The electromagnet does not work. First check whether the soldering head of the solenoid is falling off, and check if the coil is burnt out. If neither of them is abnormal, check whether the electromagnet is displaced or blocked by stolen goods, so that the bullet can not move freely. 



    标签:   热风炉 环氧地坪漆 环氧地坪 地坪 环氧地坪施工
    无锡环氧地坪 技术支持:【易商科技】