欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 新闻资讯

    如何使热风炉的烘干效率达到最高?

    2018-11-15 08:58:36 无锡盛发地坪科技有限公司 阅读

    热风炉是一种结构简单,性能稳定,维修方便成都收账干燥设备,广泛应用于水泥生产过程。我们在改革中一般应与“风,根据修改消防,材料”成都找人公司平衡,所以具体到每个部分热风炉如何改革,我们应该注意什么?一般成都收账旋转干燥器升降机改造时应注意以下几点:

    Hot blast stove is a drying equipment with simple structure, stable performance and convenient maintenance, which is widely used in cement production process. In general, we should balance the reform with "wind, fire protection according to modification, material", so how to reform each part of hot stove, what should we pay attention to? In general, the following points should be noted when upgrading the rotary dryer. 1、热空气和材料收账接触面积。材料应尽可能均匀地分布在一段烘干热风炉筒,与热空气充分接触成都找人公司材料,消除风洞材料和不均匀分布的原因。

    1. Contact area between hot air and material. Material should be distributed as evenly as possible in a section of drying hot blast stove. Material in full contact with hot air can eliminate the cause of material and uneven distribution in wind tunnel.

    2、注意热空气和材料的接触时间。我们要接触时间尽可能延长材料和热空气干燥,以达到最佳的效果。

    2. Pay attention to the contact time between hot air and materials. We should contact time to extend the material and hot air as far as possible to achieve the best results.

    3、为了使物料在运动状态尽可能,将运动中的气体流中的旋转干燥器,阳板,管壁,陈旧的消除。每单位时间的材料尽可能的运动。

    3. In order to make the material move as far as possible, the rotary dryer, the positive plate, the pipe wall and the obsolete elimination in the moving gas flow are eliminated. Material per unit time is as fast as possible.

    4、为了便于生产,安装,维修,更换。

    4, in order to facilitate production, installation, maintenance, replacement.

    5、要注意干燥机里物料在预热段,干燥,降速干燥行为。

    5, attention should be paid to the preheating, drying and drying behavior of materials in the dryer.

    应注意升降板重建的五种以上,我们可以把升降机步弧式升降机。走弧形升降板上有非常强的材料的适应性,煤泥等粘性物料不易粘在升降板,在棚板材料的运动是一个轻松自由的运动状态。同时,根据每个电弧改变不同的要求,如在预热段材料的水分含量高,我们可以提高电弧以防粘材料。

    Attention should be paid to more than five kinds of lifting board reconstruction, so we can lift the lift step arc lift. The arc-shaped lifting board has very strong material adaptability. The sticky materials such as slime are not easy to stick to the lifting board. The movement of the shed board material is a relaxed and free movement state. At the same time, according to the different requirements of each arc, if the moisture content of the material is high in the preheating section, we can improve the arc to prevent sticking materials.

    我们正在安装弧形升降板,为了使轴升降板和回转干燥机筒形成夹角,最佳倾斜角度大于或等于烘干机,进料端低,一些高排放端,形成在筒体内的螺旋。同时,间隔必须每层之间的优势,和一层升降机,升降板间距下一层之间的对准。螺旋升降机的设计,可以在缸使材料螺旋运动,从而延长物料在热风炉筒体的保留时间。

    We are installing arc-shaped lifting plate, in order to form an angle between the shaft lifting plate and the rotary dryer barrel, the optimum inclination angle is greater than or equal to the dryer, the feeding end is low, and some high emission ends are formed in the spiral of the barrel body. At the same time, the spacing must be between the advantages of each layer, and the alignment between one layer of elevator and the next layer of elevator spacing. The design of spiral elevator can make the material spiral in cylinder, thus prolonging the material retention time in hot blast stove barrel.



    标签:   热风炉 环氧地坪 地坪 环氧地坪漆 环氧地坪施工 环氧地坪翻新
    无锡环氧地坪 技术支持:【易商科技】