欢迎光临无锡盛发地坪科技有限公司官网!【环氧地坪_防静电地坪_停车场地坪_耐磨地坪】材料生产,销售和施工的高新技术企业.

    示例图片三
    网站首页 > 新闻资讯 > 环氧地坪

    环氧地坪漆施工方法及注意事项

    2018-11-08 08:06:47 无锡盛发地坪科技有限公司 阅读

    环氧地坪漆在施工过程中,拥有先进的基面处理设备、涂装施工工具及质量控制仪器是创造优良环氧地坪漆工程的有力武器。环氧地坪漆环氧地坪涂料常用施工工具与设备,据介绍,主要包括以下几个方面:

    In the construction process of epoxy floor paint, it is a powerful weapon to create excellent floor paint projects with advanced base treatment equipment, painting construction tools and quality control instruments. Epoxy floor paint, common construction tools and equipment of epoxy floor paint, according to the introduction, mainly includes the following aspects:

    施工步骤:

    Construction steps:

    1.素地处理

    1. prime processing

    ①基础素地以水泥粉光面或磨石地为准;

    (1) based on cement powder or grindstone,

    ②素地需养生28天以上,水份需8%以下方可施工素地如有不平或空鼓需加以除去;

    (2) The vegetable land should be kept in good health for more than 28 days, and the water content should be less than 8% before it can be removed if there is unevenness or empty drum in the construction of the vegetable land.

    ③用环氧砂浆补平地面;

    Third, use epoxy mortar to patch the ground.

    ④素地之油污需澈底清洗干净;

    4. The oil pollution of prime land must be cleaned thoroughly.

    ⑤施工前需保持施工素地之干燥和清洁;

    Before construction, it is necessary to keep the construction site dry and clean.

    2.底涂层

    2. bottom coating

    ①施工前需保持干净如有杂物粘附需清除依照正确比例将主剂及硬化剂混合,充分搅拌;

    1. Keep clean before construction. If there is any debris adhesion, remove the main agent and hardening agent according to the correct proportion and mix them fully.

    ②需视地面情况调整适当粘度混合完成材料需4小时以内施工完成;

    Second, it is necessary to adjust the proper viscosity and finish the material within 4 hours according to the ground conditions.

    ③底涂层养生硬化时间约8小时以上。

    3. The curing time of the bottom coating is about 8 hours.

    3.中涂层

    3. medium coating

    ①施工前需要保持干净如有杂物粘附需清除依照正确 比例将主剂及硬化剂混合,充分搅拌;

    (1) Before construction, it is necessary to keep clean. If debris adheres, it is necessary to remove and mix the main agent and hardening agent according to the correct proportion and mix them fully.

    ②将混合完成的树脂适量加入石英砂;

    (2) adding proper amount of resin to the quartz sand.

    ③使用镘刀将材料均匀涂布;

    3. Use the trowel to evenly coat the material.

    ④混合完成材料需30分钟以内施工完成;

    (4) the mixture should be completed within 30 minutes.

    ⑤施工交接处做好交接处理;

    (5) handle the handover at the construction junction.

    ⑥中涂层养生硬化时间约8小时以上。

    The curing time of middle coating is about 8 hours.

    4.批土层

    4. batches of soil

    ①依照正确比例将主剂及硬化剂混合,充分搅拌;

    1. Mix the main agent and hardener in proper proportion and stir well.

    ②使用批刀将材料涂布均匀;

    Second, use the batch knife to coat the material evenly.

    ③混合完成材料需30分钟内施工完成;

    (3) the mixture will be completed in 30 minutes.

    ④批土养生硬化时间约8小时以上;

    (4) soil curing time is more than 8 hours.

    ⑤视实际需要施工数道要求达到平整无孔洞,无批刀印及砂磨印为准。

    (5) according to the actual needs, the construction requirements of the construction must be smooth and no holes, and no batch cutter and sand print shall prevail.

    5.面涂层

    5. surface coating

    ①施工前需保持干净如有杂物粘附需清除;

    1. Keep clean before construction;

    ②使用前主剂先搅拌均匀;

    The main agent should be mixed before use.

    ③依照正确比例将主剂及硬化剂混合,充分搅拌;

    Third, mix the main agent and hardener in the right proportion and stir well.

    ④使用滚筒或镘刀将材料均匀涂布混合完成材料需30分钟以内施工完成;

    (4) use the roller or trowel to evenly coat the material and complete the material in 30 minutes.

    ⑤施工交接处需做好交接处理;

    (5) the handover should be done well at the construction junction.

    ⑥施工完成后,24小时后方可上人,72小时后方可重压(以250C为准,低温时开放时间需适度延长)

    _After the completion of construction, people can enter the building 24 hours later, and heavy pressure can be applied 72 hours later (based on 250C, the opening time should be prolonged at low temperature). 环氧地坪漆,环氧地坪涂料常用施工工具与设备

    Epoxy floor paint, commonly used construction tools and equipment for epoxy floor coatings

    环氧地坪漆是采用无溶剂优质环氧树脂及固化剂配置而成。表面平滑、美观、达镜面效果,具有耐较强酸、碱、盐、油类介质腐蚀,耐强碱性特优,耐磨、耐压、耐冲击,洁净程度较高等特点。适用于高度清洁、美观、无尘、无菌的电子、微电子行业,实行GMP标准的制药、血液制品行业,也可用于学校、办公室、家庭等环氧地坪

    Epoxy floor paint is made of solventless high quality epoxy resin and curing agent. Smooth, beautiful, mirror effect, with strong acid, alkali, salt, oil medium corrosion resistance, strong alkali resistance, excellent wear resistance, pressure resistance, impact resistance, high cleanliness and so on. It is suitable for highly clean, beautiful, dust-free, sterile electronics and microelectronics industries, pharmaceuticals and blood products industries that implement GMP standards, as well as floors of schools, offices and families.



    一、基面处理设备

    1. Base surface processing equipment

    1、磨削机:装配金刚研磨刀,用于混凝土、水磨石、硬化耐磨地面、大理石等基材表面打磨处理。

    1. Grinding machine: assemble diamond grinding tool for grinding concrete, terrazzo, hardened wear-resistant ground, marble and other base materials.

    2、便携式磨削机:用于小面积混凝土、水磨石、硬化耐磨地面、大理石等基材表面或边角部位打磨处理,亦可用于去除小面积的旧漆和油污层。

    2. Portable grinder: It is used for grinding small area of concrete, terrazzo, hardened wear-resistant ground, marble and other base material surfaces or corners. It can also be used to remove small areas of old paint and paint layer.

    3、铣刨机:用于铣刨去除旧漆层、油污层等。

    3, milling machine: for milling, remove old paint layer, oil pollution layer.

    4、抛丸设备:用于大面积混凝土、水磨石、硬化耐磨地面、大理石等基材表面抛丸处理。

    4. Shot blasting equipment: used for large area of concrete, terrazzo, hardened wear-resistant ground, marble and other base material surface shot blasting treatment.

    5、吸尘器:去除地面灰尘。

    5. Vacuum cleaner: remove dust from the ground.


    二、涂装施工工具

    Two. Coating construction tools

    1、锯齿镘刀、钉鞋、钉子辊筒:锯齿镘刀用于镘涂自流平地坪涂料,然后用钉子辊筒辊压以释出膜内空气,对于局部涂装缺陷可在涂膜表干前穿钉鞋前往修复。

    1. Sawtooth trowel, nail shoe, nail roller: Sawtooth trowel is used for trowelling self-leveling floor paint, and then the air inside the film is released by roller pressing with nail. For local coating defects, the nail shoe can be worn to repair before the film surface is dry.

    2、平底刮板:用于刮涂底漆、砂浆、腻子等稠厚地坪涂料,适合于紧贴地面刮涂。

    2. Flat-bottomed scraper: It is used for scraping thick floor coatings such as primer, mortar, putty, etc. It is suitable for scraping close to the ground.

    3、辊筒与漆刷:质量优异、不掉毛的辊筒和刷子方能获得良好的外观,通常短毛辊筒具有更好的操作性。

    3. Rollers and brushes: Excellent quality, non-hair loss roller and brush can get a good appearance, usually short hair roller has better operability.

    4、无空气喷涂机:用于喷涂施工地坪面漆,效率高,易获得良好的装饰效果,易控制涂料耗量;须根据涂料粘度及使用期选择喷泵和喷咀,以获得适合的流体压力和流量。通常电驱动或内燃机驱动的高压无气喷涂机因其良好的便携性而得到广泛应用。

    4. Air-free spraying machine: It is used for spraying floor topcoat, with high efficiency, easy to obtain good decorative effect and easy to control paint consumption; spraying pump and nozzle should be selected according to paint viscosity and service life in order to obtain suitable fluid pressure and flow rate. Usually high-pressure airless spraying machine driven by electric or internal combustion engine is widely used because of its good portability.

    5、空气喷涂设备:包括空气压缩机和空气喷枪,可用于喷涂施工低粘度的地坪涂料。

    5. Air spraying equipment: including air compressor and air spraying gun, which can be used for spraying low-viscosity floor coatings.

    6、砂浆搅拌机、铺料器与抹光机:用于施工厚层(≥3mm)树脂砂浆,将搅拌均匀的树脂砂浆用铺料器摊铺于地板上,采用抹光机抹平。

    6. Mortar mixer, paver and polisher: used for construction of thick layer (> 3mm) resin mortar. The evenly mixed resin mortar is spread on the floor with paver and polished with polisher.

    7、消泡滚筒刷:适用于地坪漆施工,可消除气泡,滚平效果好。

    7, defoaming drum brush: applicable to floor paint construction, can eliminate bubbles, roll leveling effect is good.

    8、地坪漆平口、圆口镘刀:采用锰钢材料制造,适用于地坪漆、环氧地坪漆施工。

    8. Floor paint flat mouth, round mouth trowel: Made of manganese steel, suitable for floor paint, epoxy floor paint construction.


    三、中涂打磨设备

    Three. Medium grinding equipment

    1、大打磨机:高效快速的中涂层打磨设备。

    1, large grinding machine: efficient and fast medium coating grinding equipment.

    2、抛光机与砂带机:配以80~120目的磨片及砂带,在涂装面漆前打磨砂浆或腻子层以获得平整细腻的表面;配以较粗(20~40目)的磨片及砂带亦可以用于混凝土等基材表面的简易打磨处理。

    2. Polishing machine and abrasive belt machine: with 80-120 mesh abrasive discs and belts, we can polish the mortar or putty layer before finishing paint to obtain a smooth and delicate surface; with coarse (20-40 mesh) abrasive discs and belts, we can also use them for simple polishing of the surface of concrete and other substrates.


    四、检验与试验设备

    Four. Testing and testing equipment

    1、底材表面温度及环境温湿度仪:测定涂装环境温湿度及底材表面温度以确定是否满足涂装要求。

    1. Substrate Surface Temperature and Ambient Temperature and Humidity Meter: Determine the ambient temperature and humidity of the coating and the surface temperature of the substrate to determine whether it meets the coating requirements.

    2、基材含水率测定仪:用以测定基材含水率以判定是否符合涂装要求。

    2. Substrate moisture content tester: used to determine the moisture content of the substrate to determine whether it meets the coating requirements.

    3、导静电电阻测定仪:用以测定防静电地坪的导静电电阻率。

    3, conductive electrostatic resistance tester: used to measure electrostatic conductivity of anti-static floor. 五、其它辅助工具

    Five. Other auxiliary tools.

    1、切缝机与打胶枪:用于缝隙的处理,切割机用于将缝隙切割和修饰成“V”字形或梯形(宽5-10mm)以方便填补和灌注;而打胶枪用于灌注聚氨酯弹性胶。

    1. Sewing machine and glue gun: for the treatment of cracks, the cutting machine is used to cut and modify the cracks into V-shaped or trapezoidal (5-10mm wide) for easy filling and filling; and the glue gun is used for filling polyurethane elastomer.

    2、称量与搅拌工具:较高精度的称量工具有利于按比例准确配制多组份地坪涂料,使用电动搅拌器充分快速地混合和搅拌涂

    2. Weighing and mixing tools: Higher precision weighing tools are conducive to the accurate preparation of multi-component floor coatings in proportion, and the use of electric agitators to mix and mix sufficiently and quickly.


    标签:   环氧地坪 地坪 环氧地坪漆 环氧地坪施工 环氧地坪翻新
    无锡环氧地坪 技术支持:【易商科技】